A load calculation is only as good as the inputs behind it and the design decisions that follow it.
A quality HVAC load calculation service starts with your complete construction plans and asks the right questions about your house. It delivers a room-by-room Manual J load calculation, uses Manual S to size the equipment and, when needed, Manual D to design the ducts. You should get the full set of reports behind the results, and a clear policy for revisions as decisions change.

If you’re shopping for an HVAC load calculation service, you’ll find prices and turnaround times all over the map. Some of that difference is real value. Some of it is just a quick number dressed up as a design.
A Manual J load calculation tells you how much heat enters your house in the summer and how much leaves it in the winter. It also tells you how much heat is generated inside. That’s critical information. But on its own, it doesn’t tell anyone what size equipment to install, or what duct routes and sizes are needed.
This page explains what a real load calculation service should ask you for, what you should get back, and the red flags I’ve learned to spot over decades in the heating and air conditioning industry.
Block Load vs. Room-by-Room Load Calculations
There are two types of Manual J load calculations, and it’s important to know which one you’re getting.
- A block load calculation determines the total heat gain and heat loss for the entire house.
- A room-by-room load calculation does the same thing, and also calculates the heat gain and heat loss for each individual space.
A block load takes a little less design time, which often means a lower price. But you can’t use a block load to design a duct system.
Room-by-room calculations don’t take much more design time. That’s why they’re almost always worth whatever premium there might be, within reason. Even if you don’t plan to install or change a duct system now, you’ll know how much air, proportionally, belongs in each room if you ever do. And if you never do, the next owner of your house will likely appreciate having that detail at the sale.
What a Load Calculation Alone Can’t Do
It can’t tell you what size equipment to install
Manual J tells you how much heating and cooling capacity your home needs. It can’t tell you which system can actually deliver it. That takes Manual S, and the cooling side is the harder one to get right. Two principles explain why.
- Rated capacity isn’t real-world capacity. A system’s rated capacity comes from standard test conditions, not your house’s conditions. Its real output has to be calculated for your local design conditions.
- Cooling capacity has two parts. Total cooling capacity is sensible capacity plus latent capacity.
- Sensible capacity is the BTUs needed to change the air temperature.
- Latent capacity is the BTUs needed to remove moisture from the air.
Picture the identical house built in Louisiana and in Arizona. The Louisiana house needs a lot of latent capacity to remove moisture. The Arizona house needs much less, if any. A 3-ton system might be right in Arizona, while the same house in Louisiana might need a 3.5-ton or even a 4-ton.
Manual S, which the building code points to, limits how far total capacity can exceed the load. It also requires latent capacity to meet the latent load. In humid climates, total capacity often has to go past the usual limits to meet the latent load, and the system is still compliant. Occasionally a plan reviewer flags one of my designs as oversized because they looked at total capacity alone.
Without Manual S, choosing the right size system is nothing more than a lucky guess. Learn more about Manual S equipment sizing.
It can’t design your duct system on its own
Say you have a 5-ton system moving about 2,000 cubic feet of air per minute (CFM), and no room-by-room calculation. It’s very common for a contractor to give a room with 15% of the floor area 15% of the airflow. That old-school square-footage method has no basis in accuracy.
I see the result often. A client tells me their bedroom is too hot, and they assume the duct or the whole system is too small. Often the real culprit is too much air going to the family room, dining room and kitchen. Those rooms usually have conditioned space on three sides and one exterior wall. The hot bedroom has three exterior walls, so it needs more air per square foot.
Those common rooms also tend to sit closest to the thermostat. They get more air than they need and reach the setpoint quickly. The thermostat is satisfied, and the system shuts off before the bedroom gets its share.
A room-by-room calculation shows how that air should be divided. Even then, the numbers are only proportionally correct until Manual S sets the total airflow. For example, the humid Louisiana house will likely run around 350 CFM per ton, and the dry Arizona house around 450.
The order matters: first Manual J, then Manual S, and finally Manual D to design the duct system. Learn more about Manual D duct design.
What a Quality Load Calculation Service Provider Should Ask You For
Construction plans. Accurate Manual J load calculations require comprehensive architectural plans. A service that doesn’t ask for them, or doesn’t ask about changes to them, can’t provide accurate Manual J load calculations. Full stop.
Duct system location. Ducts in a vented attic and ducts inside the conditioned space produce very different heat loads. Enter the location wrong, and the system will likely be the wrong size. If you’re weighing a sealed attic or crawl space, see what sealed attics and conditioned crawl spaces mean for HVAC design.
Structural plans (floor and roof framing). If your ducts are being designed too, and they have to route around obstructions, the designer needs accurate structural plans to create an installable duct design. For example:
- Ducts will run through floor framing cavities, or through an attic or crawl space with limited room.
- The forced air unit (FAU), meaning a furnace with an evaporator coil or an air handling unit, will sit within roof trusses. A truss framing plan confirms the equipment will actually fit.
That second point matters. If the ducts are designed around an FAU in a specific spot, and it later won’t fit there, the duct system has to be redesigned. That can raise your design fee. It can also force unwanted changes like dropped ceilings or soffits to route ducts around framing that can no longer be altered.
Which way the house faces on the lot. As the sun crosses the sky, the cooling (not heating) loads change for the whole house and for each room. North-facing glass barely affects the cooling load, while east- and west-facing glass can affect it a lot. The same house might need a 3.5-ton system facing one way, and a half ton more or less facing another. A good designer asks for a site plan showing the orientation, or at minimum asks which way the front door faces, using the 8 points of the compass (N, NE, E and so on).
A side note: in Wrightsoft, orientation is entered in two places, but the calculations use only the orientation on the drawing plan. That drawing should come with every Manual J deliverable. Whatever the software, calculations based on the wrong orientation are wrong.
On the heating side, Manual J gives no credit for solar heat gain, even though winter sun through the windows adds some radiant heat. Heating is sized for the worst case: a cold, cloudy stretch with no sun at all.
Window ratings. The HVAC design is often done before the windows are chosen. In that case, the designer should enter a reasonable estimate of the window and glass door ratings: the U-factor and the solar heat gain coefficient (SHGC).
Insulation. I look at architectural plans all day, every day, and the R-values shown are rarely what gets installed. Usually they’re a best guess, and often just the code minimum. The real decisions typically come later, once the owner and builder can compare costs, budgets and the payback on efficiency upgrades. A homeowner may switch from a vented attic to a sealed attic with spray foam below the roof deck. That changes the budget, and it noticeably changes the home’s heat gain and heat loss.
Window ratings and insulation types, locations and R-values all need to be entered correctly, and any estimates should be revised once the decisions are made. It’s garbage in, garbage out: the more accurate the information, the more accurate the HVAC design.
Inputs That Can Inconspicuously Alter the Results
Many of the entries that matter most aren’t obvious in the reports, especially if you don’t know where to look. Here are some of the most common, and several are often used to artificially inflate the results.
Duct system location, insulation and air sealing. Manual D designs your duct system. But where the ducts are, how well they’re insulated and how airtight they’ll be all significantly change the Manual J results. ConsultAir was asked to review and correct the HVAC design for an occupied custom home in Colorado. The original calculations assumed ducts in a vented attic, but the ducts were actually installed in a sealed crawl space. That single error led to a system a full ton larger than it should have been.
Air infiltration and exfiltration: how leaky the house will be. A home’s actual infiltration rate isn’t known until the thermal envelope is complete and a blower door test is done. So for new construction, the designer estimates it. ConsultAir often sees estimated rates entered far higher than they should be. Sometimes the person doing the calculations doesn’t know how to estimate a reasonable rate. Sometimes the rate is inflated on purpose so the loads justify larger equipment. Often it’s both.
This estimate cuts both ways. It should be conservative, and close to what a test will reasonably show. Entering a rate noticeably tighter than the house will actually be artificially lowers both the heat gain and the heat loss.
Outdoor design temperatures. Clients worried about an undersized system sometimes tell me they have many days well over 100 degrees every summer. Most of the time, that’s simply not the case. Extreme temperatures are memorable, and typical ones aren’t. Design temperatures aren’t meant to be the hottest or coldest day you remember, or the record from some past year. Manual J uses ASHRAE climate data, built from 25 to 30 years of weather records for each location and updated every few years. The summer design temperature is exceeded only about 1% of the hours in a year, roughly 88 hours. The outdoor temperature stays above the winter design temperature 99% of the hours in a year. Entering a hotter summer or colder winter temperature than the data calls for is one of the most common ways to inflate the loads and justify larger equipment.
Window shading. Most people who provide load calculations don’t enter window overhangs. A front porch that projects 8 feet, with the window tops a foot below it, makes a real difference, depending on orientation. So does what’s in front of the window: sunlight reflecting off a new concrete porch slab adds heat gain. ACCA calls for blinds covering 50% of the windows, at least in the bedrooms. Screens matter too. A single-hung window is entered as 50% screened, an awning window as 100%, and a window opening onto a screened porch as 100%. If your windows won’t have bug screens, tell your designer, because screens are usually entered by default. Accurate load calculations include this level of detail for the windows and glass doors.
People add heat to the house. ACCA recommends one occupant per bedroom plus one, and in most cases that’s the right number to use. Entering more occupants without a reason is another way cooling loads get inflated.
What Your Completed Residential HVAC Design Should Include
Clients often ask me to audit their load calculations. Sometimes the house is partly built and they have concerns, or just want to make sure it’s right. Other times the house is finished and they’re having comfort or operational problems. No two load calculations will be exactly the same, but most audits ConsultAir performs reveal significant errors in how the information was entered.
One recent audit shows why the reports matter. The homeowner was concerned about noise and comfort, so they requested their load calculations and sent them to me. The house had an unfinished basement with below-grade concrete walls, and two conditioned floors above it. Every wall in the calculations had been entered as a below-grade concrete wall. The calculations were of zero value, because they didn’t describe the house that was built.
Your design should include the most common reports, with enough detail for you to confirm that the entries reasonably reflect the house you’re actually building. See ConsultAir’s sample HVAC design package for a complete example.
Red Flags When Shopping for an HVAC Load Calculation Service
“Instant” results, free calculators, a firm one- or two-day promise before anyone has seen your plans, and dare I say, a price well below most other Manual J providers. Accurate load calculations take time. Fast turnaround is possible when the plans are complete and the project is simple, or when you pay a premium to move ahead of projects already scheduled. Even then, some projects can’t be rushed because of their complexity and the back-and-forth they require. Like price, turnaround shouldn’t be promised until the designer has reviewed your project in detail. And if a provider has plenty of open time, it’s fair to ask why. Quality designers with good reputations usually stay busy.
Calculations requested too early, or never revised. You can’t do the calculations before deciding whether the family room ceiling is flat or vaulted, whether the main level sits over a conditioned basement, an unconditioned basement or a slab, or even which way the house faces. Calculations done in early design and never revised after decisions like these are a red flag.
No sample project. If a provider can’t show you a sample of their deliverables, how do you know what you’re paying for? See ConsultAir’s sample HVAC design package.
No clear revision policy. Surprises happen. Decisions like window selection and insulation types and R-values are often made after the design calculations are complete. Your Manual J provider should clearly state how revisions are handled and what they cost.
Software that isn’t ACCA-approved. The building code points to residential HVAC designs based on ACCA’s Manuals J, S and D, and only ACCA-approved software complies. Ask which software a provider uses and check it against ACCA’s approved software list. ConsultAir uses Wrightsoft Right-Suite Universal, which I consider the premier software for residential HVAC design.
Not knowing who actually does the work. Many providers take your order and then subcontract the design work. That isn’t automatically wrong, but you have to wonder how thorough their review is. ConsultAir is a one-person operation. I’m David Brown, and I’m the only person who reviews your project, quotes it, communicates with you and does the design. When I’ve brought someone in to help in the past, explaining the full scope, auditing the work to my standards and sending back corrections took as long as doing it myself. It also added more chances for errors.
Thin experience behind the software. Someone may be good with computers and once had someone show them how to run Manual J, S and D. But if quality residential HVAC design were simple, the Wrightsoft user manual wouldn’t need 585 pages, and the current Manual J wouldn’t need 628.
Energy rating offered as a side service. Some energy raters add HVAC design as a second service. Some firms employ both certified raters and separate, experienced HVAC designers, and that’s fine. What matters is whether the person doing your calculations has a real heating and air conditioning industry background, not just a working knowledge of the software. See What Is an Independent HVAC Designer?
Questions to Ask Before You Hire a Load Calculation Service
Use these questions to compare providers.
Who does the work
- Who will actually do my calculations, and what is their hands-on HVAC background?
- Is any of the work subcontracted? If so, who checks it?
- Which software do you use, and is it on ACCA’s approved list?
What they need from you
- What do you need from me? Look for construction plans, where the ducts and equipment will be located, framing or truss plans (if ducts are being designed), which way the house faces, window U-factor and SHGC, and insulation.
What you get back
- Room-by-room or block load?
- A load number only, or equipment sizing (Manual S) and duct design (Manual D) too?
- Which reports will I receive, and will they show every input?
- Can I see a complete sample project?
- If there’s more than one system, does each system get its own summary?
Accuracy
- What outdoor design temperatures will you use, and where do they come from?
- How will you estimate air leakage, duct location and duct leakage?
- Will you account for window overhangs, shading and screens?
- How many occupants will you enter?
Revisions
- How are revisions handled if windows, insulation or plans change, and what do they cost?
Is the Cheapest Load Calculation Good Enough?
It depends on your goal. If you only need a building or mechanical permit, and nobody expects the submittal to match what’s installed or inspected, hire the lowest-cost provider you can find. Some of the least expensive load calculation service providers will also be more likely to simply follow your lead. For example, tell them you need a 4-ton, and they’ll make a 4-ton look correct on paper, either because they want the business or because they don’t know any better.
But if you’re paying for calculations because you see their value, accuracy is the whole point. If you can get them done for $100 but they’re not accurate, you haven’t accomplished your goal. That doesn’t mean paying the highest price anyone quotes. It means the quality of your calculations depends on the knowledge and experience of the person doing them.
Almost without exception, properly calculated Manual J loads pay for themselves just by installing the correct system size instead of a larger one. That’s before counting the efficiency gained over the life of the house, and the added comfort.
Who ConsultAir Works With
ConsultAir primarily focuses on providing HVAC design services for residential new construction projects, ideally before any heating and air conditioning systems have been installed. That said, ConsultAir also provides design services for existing homes when adequate construction plans exist, or when the project is simple enough that the homeowner can provide sketches that adequately convey the necessary information. Requests to audit existing residential design calculations are considered on any project where adequate information can be provided.
Ready to talk about your project? Request a free HVAC design consultation.
Residential HVAC Design & Home Building Resources
Rebates, codes, and trusted resources related to residential HVAC design.